MASTER CLASS CASKETS WITH A LILY

Send

The base is made of a container, and the flower is made of shiny plastic suede.

In work we will use:
- A small plastic container with a screw cap.
- paper tape.
- scissors.
- pink fabric for casket.
- a little shiny film.
- red braid.
- Moment glue.
- iron.
- shiny plastic suede in red and green.
- plastic sheet imprint.
- a toothpick.
- ear stick.
- stamens for flowers.
- glue gun.
First, start by making a flower. We make templates. From a circle 7 cm in diameter, draw three petals with a common middle in the center. We also need separate petals 5.5 cm high. In addition, we outline leaves with sharp corners.

And proceed to cutting out the details of the patterns of suede. Three triple red petal circles, separate 5 petals and 4 green leaves.

And green trimmings will still be needed to decorate the bud.

Suede under the influence of heat changes its shape, and therefore we will use an iron. Let's start with the individual petals. We apply to the hot plane the wrong side without sparkles. As soon as the workpiece begins to shrink due to heat, we remove it and put a new shape with the clubs. Press the lower edge of the petal with the thumb on the front side, and bend the part in half with the other hand on the wrong side and slide your fingers up to the edge of the petal, stretching it a little.

We make the same form on three petal circles. The middle remains untouched.

We turn to the green leaves, there are 4 of them. Need to make streaks. You can gently draw on the front with a toothpick. It will also be beautiful after processing on a print of a sheet of plastic. In this case, we place the blank from suede with the front side on the plastic, and on top we lay a white sheet of paper. Iron the iron on the part through the paper. The print is interesting.

Next, you should also add small notches on the leaves with scissors along the edge. And we apply the sheet to the iron standing sideways, and then with our fingers we make additional bends.

On the green remnants, we will also make small bends.

Now move on to making the bud. On a cotton shelf, cut off the edge on one side. We pierce this end of the stick from the wrong side in the center of the red petal circle. And we stretch to the beginning of cotton wool.

Glue "Moment" lubricate the cotton wool and the tops of the petals from the inside. Press the bottom and top, and then glue the sides and get a closed box.

Only then on the free edge of the stick do we attach the green thin details. With this we close the stem itself and decorate the bud.

Next, we proceed to the assembly of the flower. First, take the finished stamens, bend them in half and fasten the edge.

Then, in the center of the second petal circle, make a small hole and insert a bunch of stamens into it. We fix all the details of the flower on the glue gun.

Then we glue the petals with stamens into the middle of three more petals. We try to arrange the petals in a checkerboard pattern relative to the first row.

Now we still have 5 separate petals, which we fasten in a circle from the wrong side of the flower.

We get a flower with voluminous petals.

And for its decoration between the big petals we glue 4 green leaves. One cut will be free for the bud.

The flower is completely ready.

The stage has come to decorate the very foundation of the box. Take a small container whose lid diameter is 9 cm. And the lid itself is twisted.

For preliminary pasting we use paper tape. On the lid we leave a free place with a thread, but on the jar we do not touch the inner sides and threads.

From shiny foil we cut out two circles, which will be inside at the bottom of the can and lid.

They are well fixed due to the base of scotch tape.

And on the outside of the container we glue a pink cloth. We cut a strip to the size of this jar, and we make its height 1 cm larger than the existing size. We cut this excess a little with scissors and press it to the bottom of the box.

We additionally cut out a circle to close the free part of the bottom.

The cover is also treated with a cloth on top. But in addition, you need to glue the red braid, positioning along the very edge of the cover.

Now that the finished cover, we will decorate it. We try on a flower and mark the location of the middle of the lily. Then we glue the bud, the edge of the stem to the intended place.

It remains to fix the lily itself well, given the free space for the bud. And if the petals and leaves hang heavily from the roof, they should be slightly raised closer to the flower and glued. So that when you open the lid, they do not interfere with your fingers.